Update nach erstem Aufbau in der Stadtbib
This commit is contained in:
1 parent
b758784969
commit
75ce71f4df
8 files changed
+284
No files matched your search
@@ -0,0 +1,54 @@
|
||||
#include <FastLED.h>
|
||||
|
||||
// How many leds in your strip?
|
||||
#define NUM_LEDS 60
|
||||
|
||||
// For led chips like Neopixels, which have a data line, ground, and power, you just
|
||||
// need to define DATA_PIN. For led chipsets that are SPI based (four wires - data, clock,
|
||||
// ground, and power), like the LPD8806, define both DATA_PIN and CLOCK_PIN
|
||||
#define DATA_PIN 11
|
||||
#define CLOCK_PIN 13
|
||||
|
||||
// Define the array of leds
|
||||
CRGB leds[NUM_LEDS];
|
||||
|
||||
void setup() {
|
||||
Serial.begin(57600);
|
||||
Serial.println("resetting");
|
||||
FastLED.addLeds<WS2812,DATA_PIN,RGB>(leds,NUM_LEDS);
|
||||
FastLED.setBrightness(84);
|
||||
}
|
||||
|
||||
void fadeall() { for(int i = 0; i < NUM_LEDS; i++) { leds[i].nscale8(250); } }
|
||||
|
||||
void loop() {
|
||||
static uint8_t hue = 0;
|
||||
Serial.print("x");
|
||||
// First slide the led in one direction
|
||||
for(int i = 0; i < NUM_LEDS; i++) {
|
||||
// Set the i'th led to red
|
||||
leds[i] = CHSV(hue++, 255, 255);
|
||||
// Show the leds
|
||||
FastLED.show();
|
||||
// now that we've shown the leds, reset the i'th led to black
|
||||
// leds[i] = CRGB::Black;
|
||||
fadeall();
|
||||
// Wait a little bit before we loop around and do it again
|
||||
delay(10);
|
||||
}
|
||||
Serial.print("x");
|
||||
|
||||
// Now go in the other direction.
|
||||
for(int i = (NUM_LEDS)-1; i >= 0; i--) {
|
||||
// Set the i'th led to red
|
||||
leds[i] = CHSV(hue++, 255, 255);
|
||||
// Show the leds
|
||||
FastLED.show();
|
||||
// now that we've shown the leds, reset the i'th led to black
|
||||
// leds[i] = CRGB::Black;
|
||||
fadeall();
|
||||
// Wait a little bit before we loop around and do it again
|
||||
delay(10);
|
||||
}
|
||||
}
|
||||
|
||||
@@ -0,0 +1,53 @@
|
||||
#include <FastLED.h>
|
||||
|
||||
// How many leds in your strip?
|
||||
#define NUM_LEDS 240
|
||||
#define BASE_LEDS 60
|
||||
|
||||
// For led chips like Neopixels, which have a data line, ground, and power, you just
|
||||
// need to define DATA_PIN. For led chipsets that are SPI based (four wires - data, clock,
|
||||
// ground, and power), like the LPD8806, define both DATA_PIN and CLOCK_PIN
|
||||
#define DATA_PIN 14
|
||||
#define CLOCK_PIN 13
|
||||
|
||||
// Define the array of leds
|
||||
CRGB leds[NUM_LEDS];
|
||||
|
||||
void setup() {
|
||||
Serial.begin(57600);
|
||||
Serial.println("resetting");
|
||||
FastLED.addLeds<WS2812,DATA_PIN,RGB>(leds,NUM_LEDS);
|
||||
FastLED.setBrightness(84);
|
||||
}
|
||||
|
||||
// Sets LED i and all its mirrored positions:
|
||||
// i, 120-i, 120+i, 180-i, 180+i
|
||||
void setMirroredLED(int i, CHSV color) {
|
||||
leds[i] = color;
|
||||
if (120 - i >= 0 && 120 - i < NUM_LEDS) leds[119 - i] = color;
|
||||
if (120 + i < NUM_LEDS) leds[120 + i] = color;
|
||||
if (180 + i < NUM_LEDS) leds[240 - i] = color;
|
||||
}
|
||||
|
||||
void fadeall() { for(int i = 0; i < NUM_LEDS; i++) { leds[i].nscale8(250); } }
|
||||
|
||||
void loop() {
|
||||
static uint8_t hue = 0;
|
||||
Serial.print("x");
|
||||
// First slide the led in one direction
|
||||
for(int i = 0; i < BASE_LEDS; i++) {
|
||||
setMirroredLED(i, CHSV(hue++, 255, 255));
|
||||
FastLED.show();
|
||||
fadeall();
|
||||
delay(10);
|
||||
}
|
||||
Serial.print("x");
|
||||
|
||||
// Now go in the other direction.
|
||||
for(int i = (BASE_LEDS)-1; i >= 0; i--) {
|
||||
setMirroredLED(i, CHSV(hue++, 255, 255));
|
||||
FastLED.show();
|
||||
fadeall();
|
||||
delay(10);
|
||||
}
|
||||
}
|
||||
@@ -0,0 +1,83 @@
|
||||
# Wiring LED Strip
|
||||
* 240 LEDs
|
||||
* start of every LED strip is at the female connector
|
||||
* green: data
|
||||
* red: 5 VCC
|
||||
* white: GND
|
||||
|
||||
* connect green to DATA_PIN 14, which is A0 on the Arduino
|
||||
|
||||
## Wiring with External Power Source (highly recommended)
|
||||
|
||||
5V PSU USB → Arduino
|
||||
└── GND pin ─────────────────┐
|
||||
└── Data pin (A0) ──────┐ │
|
||||
│ │
|
||||
5V PSU ──── VCC ──→ LED Strip DAT GND
|
||||
└─── GND ──→ LED Strip ───────────────┘
|
||||
|
||||
|
||||
# Wiring Guide: 12 Push Buttons + WS2812B LED Strip on Arduino Uno
|
||||
|
||||
## Available I/O Pins on Arduino Uno
|
||||
|
||||
| Pin Group | Total | Usable | Notes |
|
||||
|---|---|---|---|
|
||||
| Digital D0–D13 | 14 | 12 | Avoid D0/D1 — used for Serial TX/RX |
|
||||
| Analog A0–A5 | 6 | 6 | Can be used as digital I/O |
|
||||
| **Total usable** | | **18** | |
|
||||
|
||||
## Pin Requirements
|
||||
|
||||
- 12 push buttons = 12 pins
|
||||
- WS2812B data line = 1 pin
|
||||
- **Total: 13 pins** (fits within the Uno's 18 usable pins)
|
||||
|
||||
## Suggested Pin Assignment
|
||||
|
||||
| Component | Pin |
|
||||
|---|---|
|
||||
| Button 1 | D2 |
|
||||
| Button 2 | D3 |
|
||||
| Button 3 | D4 |
|
||||
| Button 4 | D5 |
|
||||
| Button 5 | D6 |
|
||||
| Button 6 | D7 |
|
||||
| Button 7 | D8 |
|
||||
| Button 8 | D9 |
|
||||
| Button 9 | D10 |
|
||||
| Button 10 | D11 |
|
||||
| Button 11 | D12 |
|
||||
| Button 12 | D13 |
|
||||
| WS2812B data | A0 (used as digital out) |
|
||||
| A1–A5 | free for future use |
|
||||
|
||||
## Button Wiring
|
||||
|
||||
Use `INPUT_PULLUP` — no external resistors needed.
|
||||
|
||||
- Connect each button between its digital pin and **GND**
|
||||
- Button reads **LOW** when pressed, **HIGH** when released
|
||||
|
||||
```cpp
|
||||
pinMode(buttonPin, INPUT_PULLUP);
|
||||
```
|
||||
|
||||
## WS2812B Wiring
|
||||
|
||||
The strip only requires one data pin.
|
||||
|
||||
```cpp
|
||||
#define LED_PIN A0
|
||||
#define NUM_LEDS 30
|
||||
CRGB leds[NUM_LEDS];
|
||||
|
||||
FastLED.addLeds<WS2812B, LED_PIN, GRB>(leds, NUM_LEDS);
|
||||
```
|
||||
|
||||
### Power Warning
|
||||
|
||||
Each WS2812B LED at full white draws ~60mA. If you have more than ~8–10 LEDs:
|
||||
|
||||
- Power the strip from an **external 5V supply**, not the Uno's 5V pin
|
||||
- Share a **common GND** between the external supply, the LED strip, and the Arduino Uno
|
||||
@@ -0,0 +1,26 @@
|
||||
Thermometer: 4 * 60 LEDs
|
||||
alle LEDs immer an (für Farbe, den Farbverlauf muss ich noch finden, hatte da aber mal einen von blau nach rot erstellt)
|
||||
mit Status "an" (starke Helligkeit) und "aus" (niedrige Helligkeit)
|
||||
|
||||
Baselevel bei Start/Reset: 30 LEDs "an"
|
||||
Thermometer ist in 8 Sections aufgeteilt (4 Sections unter der Mitte, 4 darüber) mit jeweils 7.5 Lichtern (Umsetzung? Alternativ nur 56LEDs benutzen, damit jeweils 7 Lichter pro Section - da könnten wir einfach 4 LEDs wirklich aus lassen, die tun ja kaum was zur Sache visuell; neue Baseline "Mitte" dann bei 28 LEDs)
|
||||
|
||||
4 Fragen, pro Frage 3 Knöpfe
|
||||
2 Knöpfe sind "falsch", 1 Knopf "richtig"
|
||||
|
||||
bei falsch: Temperatur geht hoch - 1 Section geht an (aka 7 Lichter hoch)
|
||||
bei richtig: Temperatur geht runter - 1 Section geht aus (aka 7 Lichter runter)
|
||||
pro Frage nicht mehr als 1 Section an/aus; wenn Knöpfe der gleichen Frage gedrückt werden, gleiche Section ansprechen?
|
||||
|
||||
+ Animation für an/aus, also zB dass die Lichter in Reihe an/aus gehen, ggf. Animation für gleiche Section sogar 2-3 wiederholen für visuelle Deutlichkeit
|
||||
|
||||
Ziel ist es, die 4 richtige Knöpfe zu drücken - dann wäre Thermometer auf "0"
|
||||
--> Win Animation folgt (bunter Regenbogen, der hoch und runter spielt)
|
||||
|
||||
|
||||
andere Ideen:
|
||||
- Reset-Knopf, womit wieder Baseline mit 30/28 LEDs gesetzt wird
|
||||
- Cooldown für die Knöpfe?
|
||||
|
||||
angehängte Skripte:
|
||||
- potentielle Win-Animation
|
||||
@@ -0,0 +1,35 @@
|
||||
/*
|
||||
- Wiring: connect each button between its pin and GND — no resistors needed.
|
||||
- Open the Serial Monitor at 9600 baud in the Arduino IDE to see the output.
|
||||
*/
|
||||
|
||||
const int NUM_BUTTONS = 12;
|
||||
const int BUTTON_PINS[NUM_BUTTONS] = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13};
|
||||
|
||||
bool lastState[NUM_BUTTONS];
|
||||
|
||||
void setup() {
|
||||
Serial.begin(9600);
|
||||
for (int i = 0; i < NUM_BUTTONS; i++) {
|
||||
pinMode(BUTTON_PINS[i], INPUT_PULLUP);
|
||||
lastState[i] = HIGH;
|
||||
}
|
||||
Serial.println("Button test ready. Press a button!");
|
||||
}
|
||||
|
||||
void loop() {
|
||||
for (int i = 0; i < NUM_BUTTONS; i++) {
|
||||
bool currentState = digitalRead(BUTTON_PINS[i]);
|
||||
|
||||
if (currentState == LOW && lastState[i] == HIGH) {
|
||||
Serial.print("Button ");
|
||||
Serial.print(i + 1);
|
||||
Serial.print(" pressed! (pin D");
|
||||
Serial.print(BUTTON_PINS[i]);
|
||||
Serial.println(")");
|
||||
}
|
||||
|
||||
lastState[i] = currentState;
|
||||
}
|
||||
delay(50); // simple debounce
|
||||
}
|
||||
Binary file not shown.
|
After Width: | Height: | Size: 70 KiB |
@@ -0,0 +1,6 @@
|
||||
# Stand 09.04
|
||||
|
||||
* Netzteil für Arduino (LED Strip geht wohl auch ohne zusätzlichen Strom), aber schadet nichts
|
||||
* Zweites Netzteil für den Arduino selber
|
||||
* USB Kabel mit USB Type-B Port auf Arduino Seite
|
||||
|
||||
+27
@@ -0,0 +1,27 @@
|
||||
# Used Hardware
|
||||
|
||||
## Arduino Uno
|
||||
|
||||
## LED Strip für "Thermometer"
|
||||
* https://www.roboter-bausatz.de/p/1-meter-ws2812b-led-strip-wasserdicht-5050rgb-dc5v-60leds-m
|
||||
* davon 4 Stück in Reihe (kann man zusammenstecken)
|
||||
|
||||
## Buttons
|
||||
|
||||
Specification:
|
||||
Rated voltage and current: DC/AC 250V 3A
|
||||
Material: aluminium alloy, stainless steel.
|
||||
Mounting Hole Diameter: 19mm
|
||||
Contact configuration: 1NO
|
||||
Operating type: Momentary switch
|
||||
The front shape: flat head/round
|
||||
Protection class: IP65, IK08.
|
||||
Contact resistance: ≤50mΩ.
|
||||
Insulation resistance: ≥1000mΩ.
|
||||
Dielectric strength: 2000 VAC
|
||||
Operating temperature: -20°C to +55°C.
|
||||
Mechanical life: > 1,000,000 times.
|
||||
Electrical life: > 200,000 times.
|
||||
|
||||
Package contents:
|
||||
4 x push button switches.
|
||||
Reference in new issue
Block a user