diff --git a/LEDStrip/betterwinanimation-only.ino b/LEDStrip/betterwinanimation-only.ino new file mode 100644 index 0000000..47066b1 --- /dev/null +++ b/LEDStrip/betterwinanimation-only.ino @@ -0,0 +1,54 @@ +#include + +// How many leds in your strip? +#define NUM_LEDS 60 + +// For led chips like Neopixels, which have a data line, ground, and power, you just +// need to define DATA_PIN. For led chipsets that are SPI based (four wires - data, clock, +// ground, and power), like the LPD8806, define both DATA_PIN and CLOCK_PIN +#define DATA_PIN 11 +#define CLOCK_PIN 13 + +// Define the array of leds +CRGB leds[NUM_LEDS]; + +void setup() { + Serial.begin(57600); + Serial.println("resetting"); + FastLED.addLeds(leds,NUM_LEDS); + FastLED.setBrightness(84); +} + +void fadeall() { for(int i = 0; i < NUM_LEDS; i++) { leds[i].nscale8(250); } } + +void loop() { + static uint8_t hue = 0; + Serial.print("x"); + // First slide the led in one direction + for(int i = 0; i < NUM_LEDS; i++) { + // Set the i'th led to red + leds[i] = CHSV(hue++, 255, 255); + // Show the leds + FastLED.show(); + // now that we've shown the leds, reset the i'th led to black + // leds[i] = CRGB::Black; + fadeall(); + // Wait a little bit before we loop around and do it again + delay(10); + } + Serial.print("x"); + + // Now go in the other direction. + for(int i = (NUM_LEDS)-1; i >= 0; i--) { + // Set the i'th led to red + leds[i] = CHSV(hue++, 255, 255); + // Show the leds + FastLED.show(); + // now that we've shown the leds, reset the i'th led to black + // leds[i] = CRGB::Black; + fadeall(); + // Wait a little bit before we loop around and do it again + delay(10); + } +} + diff --git a/LEDStrip/test/test.ino b/LEDStrip/test/test.ino new file mode 100644 index 0000000..5c40c52 --- /dev/null +++ b/LEDStrip/test/test.ino @@ -0,0 +1,53 @@ +#include + +// How many leds in your strip? +#define NUM_LEDS 240 +#define BASE_LEDS 60 + +// For led chips like Neopixels, which have a data line, ground, and power, you just +// need to define DATA_PIN. For led chipsets that are SPI based (four wires - data, clock, +// ground, and power), like the LPD8806, define both DATA_PIN and CLOCK_PIN +#define DATA_PIN 14 +#define CLOCK_PIN 13 + +// Define the array of leds +CRGB leds[NUM_LEDS]; + +void setup() { + Serial.begin(57600); + Serial.println("resetting"); + FastLED.addLeds(leds,NUM_LEDS); + FastLED.setBrightness(84); +} + +// Sets LED i and all its mirrored positions: +// i, 120-i, 120+i, 180-i, 180+i +void setMirroredLED(int i, CHSV color) { + leds[i] = color; + if (120 - i >= 0 && 120 - i < NUM_LEDS) leds[119 - i] = color; + if (120 + i < NUM_LEDS) leds[120 + i] = color; + if (180 + i < NUM_LEDS) leds[240 - i] = color; +} + +void fadeall() { for(int i = 0; i < NUM_LEDS; i++) { leds[i].nscale8(250); } } + +void loop() { + static uint8_t hue = 0; + Serial.print("x"); + // First slide the led in one direction + for(int i = 0; i < BASE_LEDS; i++) { + setMirroredLED(i, CHSV(hue++, 255, 255)); + FastLED.show(); + fadeall(); + delay(10); + } + Serial.print("x"); + + // Now go in the other direction. + for(int i = (BASE_LEDS)-1; i >= 0; i--) { + setMirroredLED(i, CHSV(hue++, 255, 255)); + FastLED.show(); + fadeall(); + delay(10); + } +} diff --git a/Wiring.md b/Wiring.md new file mode 100644 index 0000000..b9b9977 --- /dev/null +++ b/Wiring.md @@ -0,0 +1,83 @@ +# Wiring LED Strip +* 240 LEDs +* start of every LED strip is at the female connector + * green: data + * red: 5 VCC + * white: GND + +* connect green to DATA_PIN 14, which is A0 on the Arduino + +## Wiring with External Power Source (highly recommended) + +5V PSU USB → Arduino + └── GND pin ─────────────────┐ + └── Data pin (A0) ──────┐ │ + │ │ +5V PSU ──── VCC ──→ LED Strip DAT GND + └─── GND ──→ LED Strip ───────────────┘ + + +# Wiring Guide: 12 Push Buttons + WS2812B LED Strip on Arduino Uno + +## Available I/O Pins on Arduino Uno + +| Pin Group | Total | Usable | Notes | +|---|---|---|---| +| Digital D0–D13 | 14 | 12 | Avoid D0/D1 — used for Serial TX/RX | +| Analog A0–A5 | 6 | 6 | Can be used as digital I/O | +| **Total usable** | | **18** | | + +## Pin Requirements + +- 12 push buttons = 12 pins +- WS2812B data line = 1 pin +- **Total: 13 pins** (fits within the Uno's 18 usable pins) + +## Suggested Pin Assignment + +| Component | Pin | +|---|---| +| Button 1 | D2 | +| Button 2 | D3 | +| Button 3 | D4 | +| Button 4 | D5 | +| Button 5 | D6 | +| Button 6 | D7 | +| Button 7 | D8 | +| Button 8 | D9 | +| Button 9 | D10 | +| Button 10 | D11 | +| Button 11 | D12 | +| Button 12 | D13 | +| WS2812B data | A0 (used as digital out) | +| A1–A5 | free for future use | + +## Button Wiring + +Use `INPUT_PULLUP` — no external resistors needed. + +- Connect each button between its digital pin and **GND** +- Button reads **LOW** when pressed, **HIGH** when released + +```cpp +pinMode(buttonPin, INPUT_PULLUP); +``` + +## WS2812B Wiring + +The strip only requires one data pin. + +```cpp +#define LED_PIN A0 +#define NUM_LEDS 30 +CRGB leds[NUM_LEDS]; + +FastLED.addLeds(leds, NUM_LEDS); +``` + +### Power Warning + +Each WS2812B LED at full white draws ~60mA. If you have more than ~8–10 LEDs: + +- Power the strip from an **external 5V supply**, not the Uno's 5V pin +- Share a **common GND** between the external supply, the LED strip, and the Arduino Uno diff --git a/ablaufplan.md b/ablaufplan.md new file mode 100644 index 0000000..02d83be --- /dev/null +++ b/ablaufplan.md @@ -0,0 +1,26 @@ +Thermometer: 4 * 60 LEDs +alle LEDs immer an (für Farbe, den Farbverlauf muss ich noch finden, hatte da aber mal einen von blau nach rot erstellt) +mit Status "an" (starke Helligkeit) und "aus" (niedrige Helligkeit) + +Baselevel bei Start/Reset: 30 LEDs "an" +Thermometer ist in 8 Sections aufgeteilt (4 Sections unter der Mitte, 4 darüber) mit jeweils 7.5 Lichtern (Umsetzung? Alternativ nur 56LEDs benutzen, damit jeweils 7 Lichter pro Section - da könnten wir einfach 4 LEDs wirklich aus lassen, die tun ja kaum was zur Sache visuell; neue Baseline "Mitte" dann bei 28 LEDs) + +4 Fragen, pro Frage 3 Knöpfe +2 Knöpfe sind "falsch", 1 Knopf "richtig" + +bei falsch: Temperatur geht hoch - 1 Section geht an (aka 7 Lichter hoch) +bei richtig: Temperatur geht runter - 1 Section geht aus (aka 7 Lichter runter) +pro Frage nicht mehr als 1 Section an/aus; wenn Knöpfe der gleichen Frage gedrückt werden, gleiche Section ansprechen? + ++ Animation für an/aus, also zB dass die Lichter in Reihe an/aus gehen, ggf. Animation für gleiche Section sogar 2-3 wiederholen für visuelle Deutlichkeit + +Ziel ist es, die 4 richtige Knöpfe zu drücken - dann wäre Thermometer auf "0" +--> Win Animation folgt (bunter Regenbogen, der hoch und runter spielt) + + +andere Ideen: +- Reset-Knopf, womit wieder Baseline mit 30/28 LEDs gesetzt wird +- Cooldown für die Knöpfe? + +angehängte Skripte: +- potentielle Win-Animation diff --git a/button_test/button_test.ino b/button_test/button_test.ino new file mode 100644 index 0000000..545f3ae --- /dev/null +++ b/button_test/button_test.ino @@ -0,0 +1,35 @@ +/* + - Wiring: connect each button between its pin and GND — no resistors needed. + - Open the Serial Monitor at 9600 baud in the Arduino IDE to see the output. +*/ + +const int NUM_BUTTONS = 12; +const int BUTTON_PINS[NUM_BUTTONS] = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}; + +bool lastState[NUM_BUTTONS]; + +void setup() { + Serial.begin(9600); + for (int i = 0; i < NUM_BUTTONS; i++) { + pinMode(BUTTON_PINS[i], INPUT_PULLUP); + lastState[i] = HIGH; + } + Serial.println("Button test ready. Press a button!"); +} + +void loop() { + for (int i = 0; i < NUM_BUTTONS; i++) { + bool currentState = digitalRead(BUTTON_PINS[i]); + + if (currentState == LOW && lastState[i] == HIGH) { + Serial.print("Button "); + Serial.print(i + 1); + Serial.print(" pressed! (pin D"); + Serial.print(BUTTON_PINS[i]); + Serial.println(")"); + } + + lastState[i] = currentState; + } + delay(50); // simple debounce +} diff --git a/druckknopf.jpg b/druckknopf.jpg new file mode 100644 index 0000000..a5b3c47 Binary files /dev/null and b/druckknopf.jpg differ diff --git a/einkaufsliste.md b/einkaufsliste.md new file mode 100644 index 0000000..ef70f7d --- /dev/null +++ b/einkaufsliste.md @@ -0,0 +1,6 @@ +# Stand 09.04 + +* Netzteil für Arduino (LED Strip geht wohl auch ohne zusätzlichen Strom), aber schadet nichts +* Zweites Netzteil für den Arduino selber +* USB Kabel mit USB Type-B Port auf Arduino Seite + diff --git a/hardware.md b/hardware.md new file mode 100644 index 0000000..a7546f3 --- /dev/null +++ b/hardware.md @@ -0,0 +1,27 @@ +# Used Hardware + +## Arduino Uno + +## LED Strip für "Thermometer" +* https://www.roboter-bausatz.de/p/1-meter-ws2812b-led-strip-wasserdicht-5050rgb-dc5v-60leds-m + * davon 4 Stück in Reihe (kann man zusammenstecken) + +## Buttons + +Specification: +Rated voltage and current: DC/AC 250V 3A +Material: aluminium alloy, stainless steel. +Mounting Hole Diameter: 19mm +Contact configuration: 1NO +Operating type: Momentary switch +The front shape: flat head/round +Protection class: IP65, IK08. +Contact resistance: ≤50mΩ. +Insulation resistance: ≥1000mΩ. +Dielectric strength: 2000 VAC +Operating temperature: -20°C to +55°C. +Mechanical life: > 1,000,000 times. +Electrical life: > 200,000 times. + +Package contents: +4 x push button switches.